Merck
  • Home
  • Search Results
  • Comparison of a novel TiO₂/diatomite composite and pure TiO₂ for the purification of phosvitin phosphopeptides.

Comparison of a novel TiO₂/diatomite composite and pure TiO₂ for the purification of phosvitin phosphopeptides.

Journal of chromatography. B, Analytical technologies in the biomedical and life sciences (2014-05-03)
Yang Zhang, Junhua Li, Fuge Niu, Jun Sun, Yuan Dou, Yuntao Liu, Yujie Su, Bei Zhou, Qinqin Xu, Yanjun Yang
ABSTRACT

A novel TiO2/diatomite composite (TD) was prepared and then characterized by scanning electron microscope (SEM) and Fourier Transform Infrared (FTIR). The results of SEM showed that after modification, the porous surface of diatomite was covered with TiO2. Both diatomite and TD had clear disc-shaped structures with average grain diameters of around 25 μm. Then TD and pure TiO2 were applied in the purification of phosvitin phosphopeptides (PPPs) from the digest of egg yolk protein, and a comparative study of adsorption properties of PPPs on TD and TiO2 was performed. In the study of adsorption kinetics, the adsorption equilibrium of PPPs on TD and TiO2 fitted well with the Langmuir model, and the time needed to reach adsorption equilibrium were both around 10 min. The maximum dynamic adsorption capacity of TD (8.15 mg/g) was higher than that of TiO2 (4.96 mg/g). The results of repeated use showed that TD and TiO2 were very stable after being subjected to ten repeated adsorption-elution cycles, and TD could easily be separated from aqueous solution by filtration. On the other hand, the present synthetic technology of TD was very simple, cost-effective, organic solvent-free and available for large-scale preparation. Thus, this separation method not only brings great advantages in the purification of PPPs from egg yolk protein but also provides a promising purification material for the enrichment of phosphopeptides in proteomic researches.

MATERIALS
Product Number
Brand
Product Description

Sigma-Aldrich
Sodium hydroxide, reagent grade, ≥98%, pellets (anhydrous)
Sigma-Aldrich
Sodium hydroxide, ultra dry, powder or crystals, 99.99% trace metals basis
Supelco
Sodium sulfite, analytical standard
Sigma-Aldrich
Sodium hydroxide, puriss., meets analytical specification of Ph. Eur., BP, NF, E524, 98-100.5%, pellets
Sigma-Aldrich
Sodium hydroxide solution, 5.0 M
Sigma-Aldrich
Sodium hydroxide, reagent grade, ≥98%, pellets (anhydrous)
USP
Acetone, United States Pharmacopeia (USP) Reference Standard
Sigma-Aldrich
Sulfuric acid, puriss., meets analytical specification of Ph. Eur., BP, 95-97%
Sigma-Aldrich
Sodium sulfite, ACS reagent, ≥98.0%
Sigma-Aldrich
Sodium hydroxide, ACS reagent, ≥97.0%, pellets
Sigma-Aldrich
Titanium(IV) chloride solution, 1.0 M in toluene
Sigma-Aldrich
Sodium hydroxide solution, 50% in H2O
Sigma-Aldrich
Ammonium molybdate tetrahydrate, ACS reagent, 99.98% trace metals basis
Sigma-Aldrich
Sodium hydroxide, pellets, semiconductor grade, 99.99% trace metals basis
Sigma-Aldrich
Acetone, ACS reagent, ≥99.5%
Sigma-Aldrich
Titanium(IV) chloride solution, 0.09 M in 20% HCl
Sigma-Aldrich
Sodium hydroxide, reagent grade, 97%, flakes
Sigma-Aldrich
Acetone, histological grade, ≥99.5%
Sigma-Aldrich
Acetone, suitable for HPLC, ≥99.9%
Sigma-Aldrich
Acetone, HPLC Plus, for HPLC, GC, and residue analysis, ≥99.9%
Sigma-Aldrich
Sodium hydroxide, BioXtra, ≥98% (acidimetric), pellets (anhydrous)
Sigma-Aldrich
Ammonium molybdate tetrahydrate, ACS reagent, 81.0-83.0% MoO3 basis
Sigma-Aldrich
Titanium(IV) chloride solution, 1.0 M in methylene chloride
Sigma-Aldrich
Copper(II) sulfate pentahydrate, ReagentPlus®, ≥98.0%
Sigma-Aldrich
Sulfuric acid, ACS reagent, 95.0-98.0%
Sigma-Aldrich
Copper(II) sulfate pentahydrate, ACS reagent, ≥98.0%
Sigma-Aldrich
Sodium hydroxide, beads, 20-40 mesh, reagent grade, 97%
Sigma-Aldrich
Sodium sulfite, ≥98%
Sigma-Aldrich
Acetone, ACS reagent, ≥99.5%
Sigma-Aldrich
Sodium hydroxide, reagent grade, 97%, powder