• USA Home
  • KVGLA3TTT1 - Opticap XLT30 Durapore 0.22 µm 1-1/2 in. TC/TC

KVGLA3TTT1 Millipore

Opticap XLT30 Durapore 0.22 µm 1-1/2 in. TC/TC



Quality Level   400
material   PVDF
  polypropylene housing
  polypropylene support
  polypropylene vent cap
  silicone seal
reg. compliance   meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
sterility   sterile
feature   hydrophilic
mfr. no.   Opticap®
parameter   ≤40 mL/min air diffusion at 2.75 bar (40 psig) and 23 °C (in water)
  1.0 bar max. inlet pressure (15 psi) at 80 °C
  1.7 bar max. differential pressure (25 psid) at 80 °C (Forward)
  2.8 bar max. inlet pressure (40 psi) at 60 °C
  25 °C max. inlet temp.
  3.5 bar max. differential pressure (50 psid) at 25 °C (Reverse; intermittent)
  5.5 bar max. differential pressure (80 psid) at 25 °C (Forward)
  5.5 bar max. inlet pressure (80 psi) at 23 °C
  80 psig max. inlet pressure
L   87.1 cm (34.3 in.)
cartridge nominal length   30 in. (75 cm)
diam.   10.7 cm (4.2 in.)
filtration area   2.1 m2
inlet connection diam.   1.5 in.
inlet to outlet W   15.2 cm (6.0 in.)
outlet connection diam.   1.5 in.
overall size   30 in.
impurities   ≤0.5 EU/mL bacterial endotoxins (LAL test, Aqueous extraction)
  <0.5 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
gravimetric extractables   ≤75 mg/capsule
matrix   Durapore®
pore size   0.22 μm nominal pore size
  0.22 μm pore size
input   sample type liquid
bubble point   ≥3450 mbar (50 psig), air with water at 23 °C
fitting   1/4 in. drain/vent hose barb (with double O-ring Seal)
  inlet sanitary flange
  38 mm (1 1/2 in.) inlet/outlet sanitary flange
  outlet sanitary flange


General description

Device Configuration: Capsule

T-line/Gauge Port: T-line


Double Easy-Open bag

Other Notes

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer Wetting Instructions for Filter Units with Durapore® Membrane user guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

Preparation Note

Sterilization Method
3 autoclave cycles of 60 min @ 126 °C; not in-line steam sterilizable

This product was manufactured with a Durapore® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

Analysis Note

Bacterial Retention
Samples were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM® F838 methodology.

Gravimetric Extractables: after 24 hours in water at controlled room temperature

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥3 L

Legal Information

ASTM is a registered trademark of American Society for Testing and Materials

Durapore is a registered trademark of Merck KGaA, Darmstadt, Germany

Safety & Documentation

Safety Information

Safety Information for this product is unavailable at this time.

Emprove® Dossiers

Already an EMPROVE® Program customer? Sign in to access your EMPROVE® Dossiers

Sign In
What is the Emprove® Program?

The Emprove® Program is a system providing comprehensive and thorough documentation of our filters and single-use components, pharma raw materials, and starting materials. Three document types are included with an Emprove® Program subscription:

  • Material Qualification Dossiers
  • Quality Management Dossiers
  • Operational Excellence Dossiers

Learn more about the benefits an Emprove® Program subscription can provide

Protocols & Articles
Related Products

Technical Service:

Our team of scientists has experience in all areas of research including Life Science, Material Science, Chemical Synthesis, Chromatography, Analytical and many others.

Bulk Ordering & Pricing:

Need larger quantities for your development, manufacturing or research applications?